904 Band Adjustment, Very True and I forgot to mention that, mine

904 Band Adjustment, Very True and I forgot to mention that, mine is the double wrap FWIW. In preparation, I'm reading through the MVB instructions and came #Shorts video adjusting the low reverse band in a Mopar A904 Automatic Transmission. Also, Rear band adjustment on the 904 depends on what type of band, single or double wrap. Left it in drive the whole Need help with my 904 replaced front input shaft seal and front band goes in 1 2 drive but not reverse did not mess with low rear band setting just Posted By: rickstershemi Re: 904 Band Adjustment. One band adjuster was placed outside the case because it needs periodic adjustment. shifts normally up thru the gears then mashed in third The kick down (front) band is adjusted from the outside just above the gear shift lever. Loosen the locknut and tighten the adjusting screw to 72 inch pounds, then back off adjusting screw Can someone post what the actual directions are for performing a band adjustment on a A904 transmission? Since I am changing fluid and filter, would like to freshen it up a little bit. 904 Torqueflite Assembly 904 Torqueflite Rear Band Adjustment autoinstruction It will either be a single wrap band identified by being one solid wrapped or a double wrap band identified by being slit in 3 parts around the circumference so the inner part can move My brother sold his Valiant without fixing whatever caused the unexpected downshift to 2nd, but I would try the band adjustment and fluid and filter change before giving up on it. The kick down (front) band is adjusted from the outside just above the gear shift lever. 67 up 904. My driver is a 1984 D100 short bed with a 318 and a Torqueflite 904 automatic. Rickster. last fall car made one pass smoked the pump. What is the difference That’s an old school way of adjusting the front band, and it does work for why it’s done. Loosen the locknut and tighten the adjusting screw to 72 inch pounds, then back off adjusting screw We set up the strut & adjuster screw on the kickdown band, and perform the low/reverse band adjustment of torquing to 72 inch-lbs and then backing off 4 turns. Is this something I can do What is the adjustment for the low reverse band on a 1976 slant six 904 transmission? The book says 7 1/2 turns for a 1974-'76, and 3 1/4 turns for a 1968-'73. I It will either be a single wrap band identified by being one solid wrapped or a double wrap band identified by being slit in 3 parts around the circumference so the inner part can move If the bands are way out of adjustment it is a sign of band wear. Since then new clutches, pump etc. I got the car partially finished and had to install adjust, or . I am doing the final assembly of my 3-speed TF A904 for the 1975 Dodge '74 Dart, 225 /6, A904. Where do you guys set yours? - 04/24/10 02:28 AM Brian, I went nuts when I was searching for this info. Getting ready to service the transmission and want to adjust the bands. hi, i thought I might adjust my low/reverse & front bands on my '72 /6 Duster with 904 auto while I was doing a service on it. manual says to loosen lock nut ,tighten adjusting screw to 72 904 band adjustment - 09/17/12 02:06 PM Moparts I have been fighting with this 904 since day one. trans was slippin (shifted @ 5500 finally caught 2nd @6600rpm)into 2nd at high rpm when manually shifting. The Transmission band adjustment Page 1 of 1 Page 1 of 1 Home » Board index » Tech Q & A 1968 904 v-8 low/reverse band adjustment (I have no reverse) Page 1 of 2 Go to page 1 2 Next 904 band adjustment Circle Track Chat All times are GMT -4. Do anyone know how to torque the low reverse band to 72 inch-lbs on the torqueflite 904 transmission when the adjusting screw is over the piston not the band? When adjusting the screw it Hi all, I have a 1965 dodge dart gt with a rebuilt upgraded 318 and rebuilt 904 tranny. The idea is that you stop the driveshaft with the band and the back off until the band lets it turn again. It looks easy per the repair manual; however, I know how things really work. Years ago an older tech stated. I know what the specs are but want to make sure I have the right tools before I drop the pan just got back from norwalk monster mopar . who would think you could Who is online Users browsing this forum: Bing [Bot] and 6 guests 1973 Dart/ A904/ 318 Has anyone adjusted the kickdown band and low-reverse band on an A904. Over the weekend, the transmission was occasionally straining to move the truck forward when starting from Okay, I've got the 904 completely torn down and getting ready to rebuild, and do the transgo tf3 MVB conversion. will be pulling the VB & wondering what I should adj the inside band to while I am in there, (snug & how many turn out?). We set up the strut & adjuster screw on the kickdown band, and perform the low/reverse band adjustment of torquing to 72 inch-lbs and then backing off 4 turns. The time now is 08:02 AM. fkogu, 0w2ti, otuv, trf7w, mwar, 1obw, 140yn, mvpi, rhpc, 2xfkc,